Unglaublich wieviel Zeit und Geld Du in Dein Boot investiert hast. Wahnsinn, Respekt!
Lg Martin |
Deckwaschpumpe
Hi!
Sauber machen muss "Mann" auch mal, also eine Deckwaschpumpe bauen Also Pumpe kaufen beim Chinamann aus der der Bucht https://lh3.googleusercontent.com/-n...2/IMG_0744.JPG Klemmen sind aber unpraktisch, habe ja eine 12 V Steckdose, also umbauen https://lh3.googleusercontent.com/-R...2/IMG_0745.JPG https://lh3.googleusercontent.com/-d...2/IMG_0746.JPG Schlauchzwischenstück und Bauteile https://lh3.googleusercontent.com/-U...2/IMG_0747.JPG https://lh3.googleusercontent.com/-U...2/IMG_0748.JPG Anwärmen https://lh3.googleusercontent.com/-p...2/IMG_0749.JPG Fertig https://lh3.googleusercontent.com/-O...2/IMG_0750.JPG Bestromung https://lh3.googleusercontent.com/-S...2/IMG_0751.JPG https://lh3.googleusercontent.com/-F...2/IMG_0752.JPG https://lh3.googleusercontent.com/-P...2/IMG_0753.JPG Zugentlasung https://lh3.googleusercontent.com/-o...2/IMG_0754.JPG Dichtung https://lh3.googleusercontent.com/-i...2/IMG_0755.JPG https://lh3.googleusercontent.com/-d...2/IMG_0756.JPG Bestromung, fertig https://lh3.googleusercontent.com/-t...2/IMG_0757.JPG Anschluss im Boot https://lh3.googleusercontent.com/-v...2/IMG_0759.JPG Ladegerät und Deckwaschpumpe https://lh3.googleusercontent.com/-2...2/IMG_0760.JPG Fertiges Teil https://lh3.googleusercontent.com/-K...2/IMG_0761.JPG https://lh3.googleusercontent.com/-M...2/IMG_0830.JPG Auch als Reserve-Bilgepumpe verwendbar https://lh3.googleusercontent.com/-6...2/IMG_0831.JPG https://lh3.googleusercontent.com/-b...2/IMG_0832.JPG Als Waschpumpe https://lh3.googleusercontent.com/-z...2/IMG_0833.JPG Für den Landanschluss https://lh3.googleusercontent.com/-F...2/IMG_0834.JPG Ablagebox https://lh3.googleusercontent.com/-O...2/IMG_0836.JPG https://lh3.googleusercontent.com/-b...2/IMG_0837.JPG https://lh3.googleusercontent.com/--...2/IMG_0838.JPG LGryße Mike aus Salzburg |
Bravo 12 Pumpe
Hi!
Bravo 12 Pumpe umbauen auf 12 V Bordstecker Alle 8 Schrauben öffnen, dann kommt man ins das Innere https://lh3.googleusercontent.com/-E...2/IMG_0863.JPG Fest gestellt, dass alle Schrauben locker sind, ein weiterer Betrieb hätte einen Totalverlust ergeben, weil das Zahnrad vom Motor aus Metall ist und die anderen aus Kunststoff, alles zerlegt, ein längeres Kabel eingelötet und wieder "fest" zusammengeschraubt. https://lh3.googleusercontent.com/-P...2/IMG_0862.JPG https://lh3.googleusercontent.com/-P...2/IMG_0865.JPG https://lh3.googleusercontent.com/-Y...2/IMG_0864.JPG LGryße Mike aus Salzburg |
Die Pumpe war zu mindest bei mir ein Klumpert ....zwei davon gehabt und beide nach einiger Zeit Sprünge im roten Plastik....
|
Winde -> Goliath 1600
Hi!
Windenstandumbau, nachdem der Gurt der alten Winde gerissen ist und auch keine automatische Bremse hatte, habe ich eine Goliath 1600 gekauft, klar das die Befestigungslöcher nicht paßten und durch die längere Kurbel sowieso züruck gesetzt werde musste. Etwas verbogen war die Halterung auch, also meinem Freund gebeten, eine dickere Edelstahlplatte oben anzubraten und zur Verstärkung eine Knotenblech einzusetzen. Gestern ihm gebracht, heute schon fertig und geholt. Nachdem mein Freund begeisterter Schrottverwerter ist, durfte ich noch etwas nacharbeiten https://lh3.googleusercontent.com/-y...2/IMG_0891.JPG https://lh3.googleusercontent.com/-f...2/IMG_0892.JPG Gehör- und Augenschutz https://lh3.googleusercontent.com/-O...2/IMG_0893.JPG Geschnitten mit der Flex https://lh3.googleusercontent.com/-j...2/IMG_0894.JPG https://lh3.googleusercontent.com/-P...2/IMG_0895.JPG Rüsselschutz https://lh3.googleusercontent.com/-4...2/IMG_0896.JPG Kaltverzinkung https://lh3.googleusercontent.com/-R...2/IMG_0897.JPG https://lh3.googleusercontent.com/-A...2/IMG_0898.JPG https://lh3.googleusercontent.com/-2...2/IMG_0899.JPG https://lh3.googleusercontent.com/-y...2/IMG_0900.JPG https://lh3.googleusercontent.com/-E...2/IMG_0901.JPG https://lh3.googleusercontent.com/-A...2/IMG_0902.JPG https://lh3.googleusercontent.com/-A...2/IMG_0903.JPG https://lh3.googleusercontent.com/-S...2/IMG_0904.JPG https://lh3.googleusercontent.com/-q...2/IMG_0905.JPG Handgriff https://lh3.googleusercontent.com/-Q...2/IMG_0906.JPG https://lh3.googleusercontent.com/-r...2/IMG_0907.JPG Alle Schrauben mit Loctite gesichert https://lh3.googleusercontent.com/-X...2/IMG_0908.JPG https://lh3.googleusercontent.com/-5...2/IMG_0909.JPG Mit neuer Winde https://lh3.googleusercontent.com/-F...2/IMG_0910.JPG https://lh3.googleusercontent.com/-E...2/IMG_0911.JPG https://lh3.googleusercontent.com/-8...2/IMG_0912.JPG Verlierschutz https://lh3.googleusercontent.com/-d...2/IMG_0913.JPG Wieder neue Arbeit gekauft 1) Neue Bremse mit automatischer Nachstellung (AAA Premium Brake von AL-KO) https://lh3.googleusercontent.com/-u...2/IMG_0916.JPG 2) Neue Radlager https://lh3.googleusercontent.com/-K...2/IMG_0917.JPG 3) Bremsen Spülsystem von ALKO Leider im Lieferverzug LGryße Mike aus Salzburg |
Mike die Brille steht dir gut:biere:
Sag hast du Zinkspray verwendet? Die Radlager beim WW hab ich auch erst getauscht. Was hast du Drehmoment bei der Bremstrommel? Mein Drehmomentschlüssel hatte es nicht geschafft ? Hab nach Gefühl mit Verlängerung angezogen. Man hat nur einen Versuch dann kann man eine neue Mutter kaufen ....hab ich gelernt ! |
Zitat:
Jo. Für die Bratstellen. Achsstummel 750 nm Radlager 300 nm Da kannst bald Panzerwerkzeug vom BH holen. LGryße Mike aus Salzburg |
Was hattest du Drehmoment?lf
|
Zitat:
Bei den 1637/2051 Bremsen zw. 500 u. 550Nm und bei den 2361iger Bremsen 700-750Nm |
Zitat:
2361 LGryße Mike aus Salzburg |
Mike - Mr. Marlin :cool:
|
Montage Anleitung AAA Bremse 2361
Hi!
https://lh3.googleusercontent.com/-j...O_BREMSE_1.JPG https://lh3.googleusercontent.com/-u...O_BREMSE_2.JPG LGryße Mike aus Salzburg |
Lenkrad beschichten
Hi!
Wieder mal was gemacht. Nachdem das Lenkrad eher nicht mehr so weiss war, habe ich in div. Foren gelesen, dass man Sitzbezüge oder auch Kunstleder beschichten kann, dazu habe ich Folitec in der Farbe weiss bezogen. Alles gut mit Aceton und Siliconentferner gereinigt und dann los. https://lh3.googleusercontent.com/-F...0/IMG_1138.JPG https://lh3.googleusercontent.com/-u...0/IMG_1140.JPG https://lh3.googleusercontent.com/-_...0/IMG_1137.JPG https://lh3.googleusercontent.com/-E...0/IMG_1136.JPG https://lh3.googleusercontent.com/-x...0/IMG_1135.JPG Sieht nun so aus, mal schauen ob die Farbe hält https://lh3.googleusercontent.com/-S...0/IMG_1296.JPG LGryße Mike aus Salzburg |
Bremsen- und Radlagertausch
Hi!
Weihnachten beim Frankreichurlaub ging die Bremse des Anhängers über den Jordan. Gut, dass es einen Bolzen gibt der die Auflaufvorrichtung blockiert, sonst wäre die Bremstrommel ev. zerstört worden. Das Anbremsen in einen Kreisverkehr ohne Bremse ist gewöhnungsbedürftig, aber man gewöhnt sich daran. Bei einem Zugfahrzeug mit 3500 kg sind ein Trailer mit 1500 kg ca. 40 Prozent, mit einem PKW möchte ich dies eher nicht machen. Durch Zufall sah ich, dass es nun eine selbstnachstellende Trailerbremse von ALKO gibt, die musste natürlich sofort her, war nicht ganz so einfach, die Richtige zu bekommen und auch gleich neue Radlager, geht aber mit der ET-Nummer am Typenschild der Achse. Damit es ein wenig kompliziert wird, wollte ich auch das ALKO-Brensspülsystem mit bestellen, ist jedoch nicht lieferbar für die AAA-Bremse von Alko. Geht nicht, gibt es nicht, was nicht passt wird passend gemacht. https://lh3.googleusercontent.com/-j...O_BREMSE_1.JPG https://lh3.googleusercontent.com/-u...O_BREMSE_2.JPG Ist nicht viel daran am ALKO-Bremsspülsystem für 60 Euronen https://lh3.googleusercontent.com/-W...0/IMG_1234.JPG https://lh3.googleusercontent.com/-t...0/IMG_1239.JPG Also Löcher in die Bremsankerplatte bohren, Gewinde schneiden, fertig https://lh3.googleusercontent.com/-e...0/IMG_1230.JPG https://lh3.googleusercontent.com/-l...0/IMG_1231.JPG https://lh3.googleusercontent.com/-u...2/IMG_1232.JPG https://lh3.googleusercontent.com/-9...0/IMG_1233.JPG Komplett Bremsenwechsel https://lh3.googleusercontent.com/-Y...0/IMG_1271.JPG https://lh3.googleusercontent.com/-_...0/IMG_1272.JPG https://lh3.googleusercontent.com/-y...0/IMG_1276.JPG Ups, da ist nicht mehr da https://lh3.googleusercontent.com/-L...0/IMG_1273.JPG https://lh3.googleusercontent.com/-i...0/IMG_1275.JPG https://lh3.googleusercontent.com/-J...0/IMG_1277.JPG Der Rest vom Bremsbelag https://lh3.googleusercontent.com/-j...0/IMG_1282.JPG Die Bremstrommel hat überlebt, dank Bolzen in der Auflaufeinheit https://lh3.googleusercontent.com/-6...0/IMG_1274.JPG Neue Radlager einpressen, wie einfach dies doch geht mit Kompaktlagern, nicht der Scheixx mit den Schrägrollenlager und fetten bei meinen ersten Trailern https://lh3.googleusercontent.com/-n...0/IMG_1279.JPG https://lh3.googleusercontent.com/-L...0/IMG_1280.JPG https://lh3.googleusercontent.com/-n...0/IMG_1281.JPG Für 25 Euro pro Lager, könnte man es eigentlich prophylaktisch jährlich machen https://lh3.googleusercontent.com/-e...0/IMG_1283.JPG Die andere Seite hat jede Mende Belag, jedoch nach einmal hinklopfen fällt der geklebte Belag zu Boden. https://lh3.googleusercontent.com/-Z...0/IMG_1285.JPG https://lh3.googleusercontent.com/-u...0/IMG_0916.JPG Mit 300 Nm angezogen, fertig. Kein Lager einstellen wie bei Schrägrollen. https://lh3.googleusercontent.com/-d...0/IMG_1300.JPG Fertich. https://lh3.googleusercontent.com/-D...0/IMG_1286.JPG Bei der Heimfahrt, wieder mit Bremse, doch ein gutes Gefühl. Der Rest des Spülsystem wird am Feiertag installiert. LGryße Mike aus Salzburg |
Alle Zeitangaben in WEZ +2. Es ist jetzt 15:33 Uhr. |
Powered by vBulletin
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright © 2005 - 2025 , http://schlauchboot-online.com